QO100 (4)

M0RVB

QO100 part 4

Yes, ok, this is still not about the transmission path! But I wanted to experiment a little more with the wideband part of the transponder and DATV signals. To that aim I press ganged the small HD screen from our NVR (which in turn will be wired to the large TV downstairs) and attached it the the Winterhill box. With 12V from the lab supply to the Winterhill and the 25MHz LO being fed from the diminutive Leo Bodnar mini GPS reference clock it all appears to be working as expected. This was covered in Part 2 already but today I managed to get a screenshot with four DATV feeds, although one had just dropped leaving the last image that was received. Now I need to decide whether to keep this small screen for Winterhill or swap screens with the one I use for Hamclock with the latter then on the smaller screen. I will probably do the latter as this small screen will run from USB C from the PC meaning one less socket.

Continue reading...
M0RVB

QO100 part 3

This part was going to be about the full transmission path but I am still getting the POTY and LDF4-50A line ready. Instead, I wanted to experiment with the SG Labs 13cm transverter. For the test the FT818 was dusted off and set to 432MHz FM so it would give a constant output when keyes. This fed the transverter, the output of which was put into a dummy load via a 20dB directional coupler that in turn fed a frequency counter. The output was giving 2,404MHz and was nicely stable over a couple of hours (not keyed all the time of course). When finished the transverter will be locked to a 10MHz reference from a GPSDO. The output power was around 18mW, again via the directional coupler, so about 1.8W. The FT818 was not set to full power and the PA, when finally installed has a maximum input of 250mW so some attenuation is still needed. Ok, so I have a full receive path for both transponders, I can decode FT8, hear SSB and see DATV. And I am now happy that I will be able to transmit once the PA and POTY are all in place. My next thoughts were to FT8. I have a spare Signalink and cutting a damaged Ethernet cable and adjusting the Signalink's internal wiring to suit I managed to feed audio from the SDR into wsjt-x and successfully decode FT8. For this, I separated out the four twisted pairs and assigned one for audio from the SDR, and one eventually for audio from the FT818 plus one pair if I need it for PTT. And there we are. Everything is now packed away ready for me to test the PA and finish off the POTY and RF line.

Continue reading...
M0RVB

QO100 part 2

The reason I moved the dish was, as explained in part 1 partyl due to me wanting to send and receive DATV. Having sorted out the receive parts for the narrowband transponder the next step was to set up to receive the wideband one. the LNB was originally a 4-port device which has been modified to take an external 25MHz sinewave input on one of the ports thus leaving three free. I ran three runs of RG59 from the shack, one for the 25MHz feed and two for reception. So it was relatively easy to use the second of these to receive DATV. I already had a Winterhill DATV receiver (see https://wiki.batc.org.uk/WinterHill_Receiver_Project ) and documentation for this shows how to configure it for QO100 use using two of its inputs, leaving the other two free for other purposes. A splitter combines the two 'top' ports, feeding power from the first port. With the Winterhill set up to send 18V it flips that LNB receiver to the right polarisation for the wideband transponder. QED. And it just works. I did have to fiddle with settings because when I got the Winterhill I experimented with remote access so when turned on it simply ignored the attached HDMI display. On paper that was a case of editing the winterhill.ini file and setting BOOT=local. Buit it still did not work. I could see it had started VLC players but the screen was blank. The fix for this was to edit /boot/config.txt and uncomment the line #dtoverlay=vc4-kms-v3d. Rebooting revealed the our VLC windows with the top left showing the QO100 advertising video. Tuning was another matter. There is a utility called QO-100 WB Quick Tune available from https://github.com/m0dts/QO-100-WB-Live-Tune/releases but this is a Windows package and I do not have Windows! Fortunately however it runs just fine under wine. This utility shows the occupancy of the wideband transponder and clicking on a signal instructs the Winterhill to display it. At first I forgot that when I added a receiver it needed me to specify the LNB voltage but once I worked that out all was well. I have yet to set up the audio but it all works fine. The next step is to sort out the transmission side of things. That is for part 3 but will take me a little while yet.

Continue reading...
M0RVB

QO100 part 1

Finally I had a chance to set up the QO100 dish on the side of the house. It was originally behind the harage at ground level which was not ideal as it was both a head-hitting hazard and an RF hazard, especially as I eventually want to be able to send not only SSB but also DATV which requires a higher power output than the 4W I had originally. I also wanted to copy the special GB2RS broadcast on QO100 which was scheduled for the 28th September, 2025. So, out with the scaffolding and up with the dish. That was the easy part. The disk elevation was already set so all I needed to do was point it in the right direction azimuth-wise. I nearly got that right using a theodolite app on the phone so with the aid of all relevant hardware I tuned it to max, for now anyway. It was rather amusing to have to set up a laptop and power supplies on the scaffolding as the last time I did that was at ground level. Cables came next - three runs of RG59, each around 12 metres back to the shack. These were very fiddly but worse was to come! Once I had the runs of RG59 terminated I ran a length of LDF4-50A for the transmit path (not shown and not yet connected). That was hard as our loft is on two levels and not entirely boarded and I was having to unroll the cable in one part of the loft, push it to the other part, and finally out to the dish. That was three ladders and a lot of careful moving about in the loft, made worse by the fact that a roll of LDF4-50A cable that has soent its life rolled up really does not want to go out straight! The receive setup for the NB transponder consists of the dish and LNB, a Leo Bodnar dual output GPSDO, a square to sinewave converter both of which feed the 25MHz local oscillator frequency to the LNB, a bias tee powered from the shack PSU (for now) which powers the LNB, a SDRPlay RSP2 SDR as receiver and SDRConnect running on the Mac. Finally I had everything in place, I mounted the LNB and powered everything up. And found the beacon. But there was a regular fluctuation in frequency resulting in the beacon tone being very warbly. I put that down to the fact that everything was speard across the bench but no amount of screening helped. The GPSDO was giving a good steady 10MHz and 25MHz output but feeding this into a 'scope releaved in all I can describe as a slight furryness. The 'scope showed 25MHz without variation though. At that time I remmbered tat when I alighed the dish I made a short recording and the same effect was present there, so was it the LNB? Feeding 25MHz from a function generator cured the issue but as the generator is…

Continue reading...