Radio, railways, stuff...

M0RVB

APRS fiddling

I've had a Yaesu FTM100DE for a while now and for all that while it has had a USB adapter plugged in and doing nothing. The adapter, SCU-20 came with the transceiver. Anyway, I wondered what it could be use for. The handbook discusses it being used to extract GPS data and packet data and a quick search found some software, APRSIS32 for Windows (see http://aprsisce.wikidot.com ) that talks to various transceivers. So, software loaded, I needed a driver from Yaesu. Here's where it begins to get a little tedious as those of you who have had to go looking for drivers will no doubt know. First port of call was the Yaesu site and a search for FTM100. Ok, found that. Now 'files' and ... a driver for a SCU-19. Searches for SCU-20 found a PDF which contained the filename of the driver but not the source. I eventually found it... under the files for the FTM400. And that was the hardest part. Driver in, USB lead connected, APRSIS32 loaded and a few parameters configured and there is it. The software will also send messages etc. but apparently Yaesu do not allow their kit, or at least the kit I have send data out from sources that are not internally generated. (ref: https://groups.io/g/APRSISCE/topic/76092175 ) Oh well, I didn't get the radio for APRS anyway but it's a bit annoying. Anyway it was a fruitful 'have wire, must make it do something' episode. The APRSIS32 software is neat and full of functionality, and quite intuitive. It also has a whole support group on groups.io.

Continue reading...
M0RVB

10GHz experiments

I am slowly getting kit together for 2.4GHz and 10GHz. So far I have SSPAs for both bands, one which will hopefully enable me to get onto the wideband DATV part of QO100, and the other as part of a 10GHz setup. I got a Goobay LNB from eBay a while ago. My plan for this was to build it into a POTY for QO100 but I acquired a ready-made POTY that had an input for a 25MHz clock signal and that all works fine. So I wondered if this LNB could be persuaded to receive 10.368GHz. Fortunately I had not got as far as pulling it apart. The LNB is marked 67321, input range 10.7 to 12.75GHz, local oscillator frequencies at 9.75 and 10.6GHz. Reading up on LNBs in general was advice that one can use the 24th harmonic of a 70cm handheld held in front of the LNB to generate a 10GHz signal. This I had to try and with a bias-tee feeding 12V to the LNB and an SDRPlay RSP2 and SDRUno it does in fact work. Transmitting on 432MHz should have, in theory generated a peak at 618MHz on the SDR (10368 - 9750) but it actually came out at 618.6MHz. Well, close, and at least it is something. I checked the radio output on a counter which showed 432.0018MHz. I also checked the SDR receiving 432MHz and it showed it correctly. So the LNB is not quite there but this was only a quick test and it does show the way to test my eventual transmitter actually transmits. The next step is to assemble a 10GHz transverter and the parts for this are hopefully on their way.

Continue reading...
M0RVB

WANTED!

I am searching for a few things and given the lack of accessible (to me) radio rallies I have listed those items I need below - please email me (wanted 'at' m0rvb.uk) if you are selling anything suitable... Microwave signal generator, to get past 10GHz 32V 15A (or higher) power supply (prefer linear) 10.5V 12A power supply - I have a 12V 15A PSU from eBay which will adjust down to 10.4V so I will try this N socket to waveguide transition for 10GHz (SMA socket would do) 10GHz waveguide attenuator 10GHz waveguide load / dummy load, at least 30W

Continue reading...