Radio, railways, stuff...

M0RVB

QO100 part 1

Finally I had a chance to set up the QO100 dish on the side of the house. It was originally behind the harage at ground level which was not ideal as it was both a head-hitting hazard and an RF hazard, especially as I eventually want to be able to send not only SSB but also DATV which requires a higher power output than the 4W I had originally. I also wanted to copy the special GB2RS broadcast on QO100 which was scheduled for the 28th September, 2025. So, out with the scaffolding and up with the dish. That was the easy part. The disk elevation was already set so all I needed to do was point it in the right direction azimuth-wise. I nearly got that right using a theodolite app on the phone so with the aid of all relevant hardware I tuned it to max, for now anyway. It was rather amusing to have to set up a laptop and power supplies on the scaffolding as the last time I did that was at ground level. Cables came next - three runs of RG59, each around 12 metres back to the shack. These were very fiddly but worse was to come! Once I had the runs of RG59 terminated I ran a length of LDF4-50A for the transmit path (not shown and not yet connected). That was hard as our loft is on two levels and not entirely boarded and I was having to unroll the cable in one part of the loft, push it to the other part, and finally out to the dish. That was three ladders and a lot of careful moving about in the loft, made worse by the fact that a roll of LDF4-50A cable that has soent its life rolled up really does not want to go out straight! The receive setup for the NB transponder consists of the dish and LNB, a Leo Bodnar dual output GPSDO, a square to sinewave converter both of which feed the 25MHz local oscillator frequency to the LNB, a bias tee powered from the shack PSU (for now) which powers the LNB, a SDRPlay RSP2 SDR as receiver and SDRConnect running on the Mac. Finally I had everything in place, I mounted the LNB and powered everything up. And found the beacon. But there was a regular fluctuation in frequency resulting in the beacon tone being very warbly. I put that down to the fact that everything was speard across the bench but no amount of screening helped. The GPSDO was giving a good steady 10MHz and 25MHz output but feeding this into a 'scope releaved in all I can describe as a slight furryness. The 'scope showed 25MHz without variation though. At that time I remmbered tat when I alighed the dish I made a short recording and the same effect was present there, so was it the LNB? Feeding 25MHz from a function generator cured the issue but as the generator is…

Continue reading...
M0RVB

IT changes

My 'pigate' Pi is no more. Well, it still exists, but has been decommissioned. It has a story going back a few years. It began life as one of thre Pi systems in the blue metal box that has just been scrapped but was later moved to its own 3D printed box. It ran a varying number of packages, taking over the ADBS logger that was on a Pi in the loft and also running Hamclock and a decoder for our weather station. But recently the PoE HAT fan has been considerably annoying and Hamclock always seemed to push the load up. Enter a new (old) fanless PC. This is an eBay purchase, a Wyse 5060 made by Dell and arrived today. And it has a story of its own! First off it was sold as used with an un-activated Windows 10 on board but it appears to be new due to the packaging. The first step for this PC was to install Lubuntu 24.04 LTS but on powering it up it has a BIOS password set. Fortunately the password is known and available via the Web. It turns out the Wyse 5060 is a thin client aimed at having apps accessed across the network. But regardless it is a full PC, 265Gb SDD, 4Gb RAM and an AMD 64 bit quad core processor at 2.5Gbps, a decent upgrade from the Pi 4B of pigate. Setting the thing up was relatively painless except the dump1090 and fr24feed setup failed twice so got deleted entirely and installed again. I missed something because after that it works fine. I still need to finish the setup as temperature recording is very different to the Pi and to my Lenovo server. It is currently reporting 50°C via 'sensors'. This system actually replaces two Pi systems and potentially a third one. The other two are one Pi with a switchable USB hub that powers the little LoRa modules (radiosonde receiver and TinyGS station - it did have a Meshcom node on too but it keeps crashing), and one running SatNOGS. I see no reason why I can't move the SatNOGS stuff across later on. Of course this PC has its own PSU - 19V - so it has taken up a wall socket whereas the Pi systems are all PoE powered. It is time I purchased a long power strip anyway. The other change is the QRP Labs shack clock has been retired, which also meant the dedicated 5V linear PSU has also gobe. Since I got the DX Patrol GPSDO it became evident that the shackl clock does not tick right - what I mean is the display is about 1 second slow. Having multiple clocks is always an issue, but four of them agree with each other to the second so the delay on the shack clock has become a but of a nuissance. So clock-wise I have the DX Patrol showing UTC which, although the display is rather small is easy enough…

Continue reading...
M0RVB

Bye bye blue box

For some time now my pi-star node was in a fairly large blue box. Originaly this box had three Pi systems plus a 5V PSU but over the months two of those systems were either shut down or relocated to their own 3D printed box and powered via a PoE HAT. So the blue box, measuring some 240x110x190mm was pretty much empty. Since I built a M17 hotspot out of a Pi and a Nextion screen I found a 3D printable box specifically for the 3.2" Nextion. So I printed this and a second one for pi-star. This has saved quite a bit of shelf space. The case is not fully ideal because in the case of the pi-star node the Nextion is connected via a USB to TTL converter which sticks outside the case. The M17 node has a Zumspot USB radio which again sticks out the side. But it will make a good basis for designing a wider box that will encompass the USB bits.

Continue reading...