Radio, railways, stuff...

M0RVB

More ATV fiddling

After finding the dead LCD screen that was to be a 5.6GHz ATV receiver it also turned out that the 7" Pi screen on my Portsdown setup had similarly died - just white lines on the screen. No amount of stripping, reassembling and general fiddling fixed it. A new screen did. Anyway, I now have a Winterhill receiver. This came from a fellow ham and saved me building one. As is usual with any new box one absolutely must try it right away, which is how I discovered the bust screen on the Portsdown. After that was replaced I successfully sent a test card 40 inches across the desk! Small steps... and at least the Winterhill is in a nice box unlike my Portsdown which is still waiting for a suitably sized case - why is it all the nice metal boxes are a few mm lower than the 7" display needs. Huh.

Continue reading...
M0RVB

5.6GHz experiments

I had a quick fiddle with the box of bits that should by now - in fact by a year ago - be a 5.6Ghz ATV transceiver. I now have a couple of Gibeon flat panel antennas which claim 24dBi as mentioned in the excellent resource on this topic at http://5-6ghz-atv.co.uk/ So, let’s have a play. I got a rather old fashioned Sandisk Photo Album, a slab of plastic that takes 5V and will present photos (and videos and sound files) to a TV via an AV output and the typical red, white and yellow RCA plugs. First off I  needed to make sure this worked. So, what has an AV input… er… Bedroom TV? Nope. An older Sony TV in another bedroom does and so it was plugged up. And nothing. Problem 1, it seems to take an age to turn on in response to its remote control. No switch of course. Problem 2, it would not read anything on the SD card I had with a test card image on. The only clue is it needs a ‘JPEG (Baseline, up to 16 Megapixel)’. No idea what I had produced via GIMP on the Linux box but it would not find anything at all. Maybe it’s the SD card. I found a very old 32Mb (!) SD card with some sundry photos on and those were fine. Ah, so maybe it cannot read big SD cards. Copied the test card file onto that and now it at least finds the card but says the format is unknown. After 3 iterations I fed the jpeg into Windows Paint, saved it (as jpeg) and it worked. And success, I can send the test card image to the TV via the TS832 transmitter and RC832 receiver. Next, I tried the flat panel antennas and they worked too, not that I would have expected any less as the little rubber duck antennas worked fine. However, offering the AV to my 12V monitor (ex eBay car reversing screen) just showed lines. No amount of shouting fixed this and it would appear that this monitor has simply died, perhaps having got fed up waiting in a box all this time. Anyway, now I need to actually construct the thing properly and work out a mount for the antennas.

Continue reading...
M0RVB

Spectrum analysers

I’ve been looking for some time for an affordable (i.e. used) and useful ranged (i.e. not cheap!) spectrum analyser. Obviously I want DC to light but don’t need it and don’t want to sell the house for a bit of test gear. I have a TinySA which is good to 960MHz but I will need a higher frequency range as I fiddle more with microwaves. The ultimate, e.g. a Rigol or Siglent LCD type device is just far too expensive. Nice to have yes but something one would need to be using all the time in order to justify it. Then I came across Satsagen - http://www.albfer.com/en/2020/02/21/satsagen-2/ Satsagen runs under Windows and by default uses an Adalm Pluto as its interface to the real world. The software even does the necessary to upgrade the Pluto to the ‘full’ range of 70MHz to 6GHz (you can do this easily by hand but it’s nice of the software to do it anyway). The software has three basic function too - spectrum analyser, spectrum analyser with tracking, and generator. So, one PC, one Pluto, Satsagen and you get a pretty decent 70MHz to 6GHz spectrum analyser, tracking generator and signal generator. I have not yet delved into all the functionality and only carried out a couple of quick tests on a handheld and on my 70MHz transverter, plus a very quick test of a FPV transmitter (TS832) up at 5.6GHz. It will work with other devices such as the HackRF and the RTL dongle but it seems so useful I purchased a Pluto just for it (yeah, ok, I can use it for other stuff too but hey)

Continue reading...