Radio, railways, stuff...

M0RVB

Zigbee randomness

Recently the outside lights here decided to switch off at random intervals for no apparent reason. There are 5 different controllers, two being Zigbee bulbs and the others Zigbee switches. All use 2.4GHz. All had been running reliably for maybe a year. On/off cycles are controlled by scripts on the server as well as manually via an app. In each case whichever set of lights had gone out did report as being off and would turn back on via the app. Some days there was no issue, on others at least one would go off at some point. The Zigbee bulbs never failed, just the switches. There was no evidence of any commands being sent to turn the lights off, but there was the occasional error being reported. Rebooting the server made no difference. A power cycle of the server seems to have cured the issue so I am considering it likely to be the Zigbee transceiver itself. This is now nagging at me to figure out what happened and presumably it will reoccur some time in the future. Too many other things to sort out though!

Continue reading...
M0RVB

Shack networking

It's surprising just how many things one gathers that need Ethernet. Having just made an NTP server out of a Raspberry Pi that took the last port in my 8+2 port PoE switch I needed more ports. The switch is a Netgear GS110TP, 8 Ethernet ports and up to two SFP modules for interlinking. So I have added a second GS110TP linked to the original one via a short fibre lead and two SFP transceivers. The house now has 4 Ethernet switches, all Netgear, making 48 Ethernet ports in total but not all in use, plus 3 wifi access points, Netgear again and all PoE powered. Actually I could have settled for a non-PoE switch as the additional one but this one came cheap, and new in box. All the switches and access points do SNMP too, centrally monitored using MRTG. Why? Because they can!

Continue reading...
M0RVB

A GPS based Raspberry Pi Stratum 1 NTP server

I decided to make my own Stratum 1 NTP server for the home. No, I don’t need the accuracy, but localising stuff like that is always interesting. So, I recently purchased an Uputronics GPS HAT from Pi Hut which is marked Raspberry Pi GPS+RTC Rev 6.4. It arrived next day along with some other bits. I also got another PoE HAT and already had a Pi 4. Raspbian installed on an SD card – this time I remembered to first set it up to work via ssh – and the Pi booted ok with the GPS board flashing it’s ‘time pulse’ LED once per second. I followed instructions on the web, in particular from the two websites shown at the bottom of this post. Initial setting up of the Pi involves the use of raspi-config to stop the serial port login shell but leaving the port enabled, and disabling serial getty and bluetooth. At this point, doing cat /dev/ttyAMA0 should return data from the GPS receiver but all I got was garbled characters. More on that later. The next step was to enable PPS support which involves modifications to /boot/config.txt and a module adding to /etc/modules, plus downloading pps-tools. Running sudo ppstest /dev/pps0 looked ok but again, more on that later. Next was to install gpsd and modifying /etc/default/gpsd plus setting it up to run at boot time. After a reboot running sudo service gpsd status returned valid information. The gpsd-clients package was installed which includes gpsmon. Running gpsmon showed that all was not well. It generated a few lines but nothing that meant any sense. I then returned to sudo ppstest /dev/pps0 and noticed this time that all it was giving was timeouts. I may well have missed this in my haste earlier as it reports ok, but then gives timeouts. An, unfortunately not recorded web page suggested adding arm_64bit=0 to /boot/config.txt and after rebooting sudo ppstest /dev/pps0 now produced a valid line, once per second. Ok. Retracing my steps I ran gpsmon again to take a closer look and noticed that in the few lines it managed to display was the entry ‘”bps”:9600’. That was the lightbulb moment. The GPS board defaults to 115200. Stopping gpsd and running minicom -b 115200 -o -D /dev/ttyAMA0 produced valid GPS data. Modifying /etc/default/gpsd to set the baud rate to 115200 (GPSD_OPTIONS=“-n -s 115200”) fixed the issue. But, gpsmon still does not produce all the output that I had expected, in particular it does not populate the time and date fields. Running cgps does show valid information and suggests that all is well and there is something I am missing regarding gpsmon. At the end of the day it all appears to be working fine. The next package installed was chrony. This all went to plan and running chronyc and its sources and sourcestats options showed valid data after the system had settled down for a couple of minutes after boot. The final leg of this journey was to set up various…

Continue reading...