Radio, railways, stuff...

M0RVB

More rattling about...

Well I fiddled with the teleprinter some more, wondering if I could at least get it to print with just 30-0-30VDC - it needs 80-0-80. Nothing. I tried connecting directly to the relevant pins for the receiving relay but could not feel any resistance when this was applied. Odd, because I could measure its resistance with a multimeter, so what's up. Strangely the next time I tried I could no longer measure the resistance. Might have been me. Then it occurred to me that on the 444 everything comes out on the 50-way D connector and you can get directly at the receiver coil, and I can see the relevant ohms. So, re-wiring the lash-up and still with 30-0-30V and with a resistor in series just in case and it burst into life. Almost. It did print, or rather tried. It got most of the letters wrong, but is at least trying. Most likely the voltage is just not quite enough, or my lash-up resistor is denying it sufficient current but I'd rather not risk the coil right now. However, and more of a concern was that although it went through the motions, the carriage did not move. It was stuck fast and no amount of fiddling would move it. After pouring over the workshop manual there seemed to be a lever in the wrong position. Moving this freed it up and it does now move with keypresses, even though the letters are wrong. Nearly there then... the ribbon is not rotating but there is at least one broken spring so hopefully that's an easy fix. All I need now is a proper TU.

Continue reading...
M0RVB

The Creed lives

Getting to grips with the Creed 444... everything seemed fine and it all rotated ok by hand so with the help of eBay I got the proper power socket and wired it up today. Things did not go entirely to plan... 1st attempt. Lots of loud noise from the motor. Well, at least it spins... the motor has a height adjustment at the rear which engages the worm with the drive gear at the front and this was completely undone. Adjusted... 2nd attempt. The lights went out! Hmmm. So, a tiny strand of copper wire had linked between the earth and live on the plug. Yes, the same one I had just soldered up carefully. Grrr. 3rd attempt and it runs. Key presses work the sequence, the WRU works too. As yet no print as I need to put a ribbon on and some paper in, but more importantly sort out the data side of things. I wonder what the WRU says... I could work it out by hand but I'll leave that until I get it to print. Equally, I wonder if I can find a blank one to put my callsign into... now that would be an ideal candidate for 3D printing! (can I use this as a reason to buy a 3D printer...) The motor and gear makes a particular whirring sound and a useful Youtube video of someone testing one of these beasts sounds the same, so that's good. There is a rattle which I need to locate but I still need to take the unit apart anyway and make sure everything is properly oiled. I wonder if the kids will believe that we used to use similar machines as input/output terminals on the mainframe at work in the 1980s!

Continue reading...
M0RVB

Good old days...

So I now have a Creed 444 teleprinter. I've been after a teleprinter for about 2 years now. When I was still at school I used to buy, strip, repair and sell Creed 7E's - maybe 7 or 8 passed through my hands and on to others for pocket money. Back then I had two 7Es for myself, as well as a tape reader, tape punch and a valved TU hanging off a B40 / B41 setup. Weight was not an issue in my basement workshop... But I've never had one of the more modern units like the 444 (yes, modern is a relative term here!) Having manhandled the beast from the car to the workshop I now need to learn how it is put together so I can be sure it's not going to fly into bits when I power it up. However, hopefully I'll get it running and then get an interface set up. I doubt it will be allowed in the shack (aka the little bedroom) so it may well have to run in the workshop - but that does give the excuse to acquire a nice old comms receiver to go with...

Continue reading...