Packet progress...

M0RVB

I actually achieved something. Makes a change!

At this stage I must state that I overlooked the fact I have an FTM100 and it has a suitable interface! Ok, no way I am going to fiddle soldering a 10-pin mini-DIN plug even if I had one, so I ordered a CT167 cable from www.JGTech.com  which arrived within two days. I already had a stock of D9 plugs. With the NinoTNC connected to the Windows PC the APRSIS32 software could send and receive APRS to/from my FT2D (no APRS activity round here other than a receive-only igate).

But packet was a tad more problematic. I wanted to use the Windows PC + Signalink + FT817 setup which means using QtSoundModem on the PC, but I also needed a program to talk to the TNC. QtTermTCP will via KISS but neither the Mac or Linux version had KISS anywhere to be seen, only AGW. And any mix of QtSoundModem and QtTermTCP on the Windows PC generally resulted in nothing talking to anything, which is probably my fault but it definitely got in the way.

So... I set up an old Pi 3B with the LinBPQ software, connected the NinoTNC / FMT100 to that and set up a test configuration. I then ran up QtSoundModem on the Windows PC talking to the FT817, and QtTermTCP on the Mac talking to the Windows QtSoundModem via AGW. And... nothing! The node sent broadcasts which were picked up by QtSoundModem etc. but connects to it all failed.

I noticed that if I sent APRS from the FT2D the OK LED on the TNC would light, but if I sent anything via QtSoundModem only the DCD flashed, no OK. Data issues then. It was then that I realised that in my earlier fiddling about with QtSoundModem I had all the various options in weird modes. Turning off FX25 and IL2P in the modem setting cured it (and no, I have no idea why I had them switched on!), and I could then connect. Success.

So, packet radio across the shack, using two radios, three computers and a NinoTNC.

Next steps... in theory anyway... I have a Tait TM8110 on order via eBay and a cable on order, I already have the programming lead and software. If all goes to plan I may even be able to build a packet node and get a NoV for it. As there is nothing at all round here then this may be a start if I can get others interested. I am to far away from other nodes in the progressive national packet network, but, early days...

You should also read:

M0RVB

Packetering

Made some useful progress on packet radio today. I managed to access a node in Scotland and one near the south coast on 40m, 300 baud. This was using QtSoundModem on the Linux box connected to the FT450D via a Signalink, fed into the random length wire in the loft. Access was via EasyTerm running on the Windows PC at first, but then I managed to compile QtTermTCP so ran that on the Linux box instead. A bit of fun but it proves the possibility of using 40m to interconnect where there is currently no VHF or UHF paths here. Fingers crossed once I get some wire and metal in the air things will only improve.

Continue reading...
M0RVB

Packet progress...

My second NinoTNC is built. The parts came today from Mouser in a huge box. I need to adjust the case a little to make it fit nicely but now I have this one I can go mobile and see how access to GB7RVB is. So far, no-one has connected (and yes, the antenna is still in the loft!) I did find a TNC program for the Mac called KISSet which works fine once I remembered to put my callsign in! I wondered why it was sending data and GB7RVB's TNC was receiving - no callsign. Twit. It worked fine after that.

Continue reading...
M0RVB

Packet mailbox NoV

I now have a NoV for GB7RVB, a packet mailbox on 144.950MHz. It is currently set for AFSK AX25 at 1200 baud, though may move to more modern IL2P 4800 baud after trials. It is located here in IO93eu and I would be interested in reports if anyone manages to connect to it. The only service currently enabled is local chat. Early days... it's a bit of a backwater here with no packet and hardly any APRS activity. Maybe this will start it as there are moves elsewhere to build up a national packet network. If one or two other nodes pop up between here and the emerging networks we could make links. If you do not have a hardware TNC it is possible to use software, for example I have successfully used QtSoundModem to drive a Signalink and my FT817, and QtTermTCP to connect via AGW to the modem, with the FT817 set to 144.950 and packet mode. GB7RVB is currently based on the LinBPQ package and runs on a Raspberry Pi 3B, with a NinoTNC (see my earlier post about having built that). It is currently driving an FTM100 set for 5W but will be using a Tait…

Continue reading...